PRODUCT

AC Motor

□80mm 40W

Product Kinds

1Ph. Motor
CONTINUOUS DUTY

Products List

■ PERFORMANCE DATA (DUTY : CONTINUOUS)

Motor Type Output
(W)
Voltage
(V)
Freq.
(Hz)
Rating Starting Condenser
Input
(W)
Current
(A)
Torque
(kgf·cm)
Speed
(rpm)
Torque
(kgf·cm)
(V) (㎌)
IH8PF40-10 40 1ø100 50 80 1.00 3.12 1250 2.30 250 10.0
60 80 1.00 2.51 1550 2.30
IH8PF40-11 1ø110 60 100 1.00 2.60 1500 2.60 250 10.0
IH8PF40-20 40 1ø200 50 70 0.40 3.12 1250 2.30 450 2.0
60 70 0.40 2.51 1550 2.30
IH8PF40-22 1ø220 60 80 0.40 2.51 1550 2.50 450 2.0
IH8PF40-1U 40 1ø115 60 100 1.00 2.51 1550 2.50 250 8.0
IH8PF40-2C 33 1ø220 50 90 0.36 2.68 1200 2.50 450 2.5
38 1ø240 50 110 0.36 3.08 1200 2.80
  • Motor Type은 감속기 직결용인 피니언축으로 표시하였습니다.
    STRAIGHT축의 모터를 희망하시면 Motor Type의 PF를 S로 바꾸어 주문하십시오.
  • 그린상자표시한 모터는 UL 또는 CE규격을 적용한 TP(Thermal Protect) Type입니다
  • For motor with straight shaft. please write S in place of PF in Motor Type
  • Motor Type in green screen represents the motors with TP(Thermal Protect) according to  UL or CE regulation.

■ RATED TORQUE OF GEARED MOTOR

(unit : kg·cm)

Speed of Geared Motor rpm 500 300 200 120 100 60 50 30 20 15 10
Gear Ratio 50Hz 3 5 7.5 12.5 15 25 30 50 75 100 150
60Hz 3.6 6 9 15 18 30 36 60 90 120 180
IH8PF40 + 8H□FM 7.6 13 19 32 38 57 68 100 100 100 100
IH8PF40 + 8H□FB 7.3 12 18 31 37 55 66 100 100 100 100
  • 그린상자표시한 감속비의 감속기는 출력축의 회전방향이 모터축의 회전방향과 반대로 됩니다.
  • 감속모터의 회전수(Speed of Geared Motor)는 모터의 회전수 (50Hz에서 1500rpm, 60Hz에서 1800rpm)를 기준하여 산출하였습니다.
    실사용시의 회전수는 부하의 크기에 따라 위의 표보다 2~15% 작게 됩니다.
  • 하얀상자부에는 감속비를 지정하여 주십시오. 감속기는 별도로 판매 됩니다.
  •  The rotation of geared motor in green screen is reverse of motor rotation. · 
  •  Speed of Geared Motor is based on motor synchronous speed. In normal operation, the speed will
  •  be 2 to 15 percent lower than above figure. 
  •  When ordering gear head, please fill blank □ with gear ratio.

■ MOTOR(STRAIGHT SHAFT)IH8S40WT 1.7kg

■ GEARED MOTORIH8PF40 + 8H□ FM(8H□ FB)WT 1.7+0.5/0.6kg

■ BOLT SIZE

No L(mm) GEAR RATIO BOLT SIZE
01 32 1/3 ~ 1/20 M5×60
02 42 1/25 ~ 1/200 M5×70

■ KEY SPEC

■ WIRING DIAGRAM

   
  • 모터의 회전방향은 샤프트 끝쪽에서 볼때의 회전방향입니다.
  • 모터의 회전방향 전환은 모터가 완전히 정지한 후 실시하여 주십시오.
  • The direction of rotation is seen from the end of motor shaft.
  • Change the rotation direction of the motor only after the motor stops completely.