PRODUCT

AC Motor

□90mm 180/200W

Product Kinds

1Ph./3Ph. Motor
CONTINUOUS DUTY

Products List

■ PERFORMANCE DATA (DUTY : CONTINUOUS)

Motor Type Output
(W)
Voltage
(V)
Freq.
(Hz)
Rating Starting Condenser
Input
(W)
Current
(A)
Torque
(kgf·cm)
Speed
(rpm)
Torque
(kgf·cm)
(V) (㎌)
IH9PU180-10 180 1ø100 50 330 3.50 13.48 1300 6.20 250 30.0
60 330 3.50 10.95 1600 6.00
IH9PU180-11 1ø110 60 380 3.50 10.95 1600 7.00 250 30.0
IH9PU180-20 180 1ø200 50 320 1.50 13.48 1300 6.20 450 6.5
60 320 1.50 10.95 1600 6.00
IH9PU180-22 1ø220 50 360 1.50 10.95 1600 7.00 450 6.5
IH9PU180-2C 150 1ø220 50 400 1.32 11.68 1250 6.60 450 7.0
180 1ø240 50 400 1.32 14.02 1250 8.00
IH9PU200-32 200 3ø220 50 400 1.20 14.98 1300 30.00
60 400 1.20 12.17 1600 25.00
IH9PU200-33 200 3ø380 50 400 0.74 14.98 1300 30.00
60 400 0.74 12.17 1600 25.00
IH9PU200-34 200 3ø380 50 400 0.64 14.98 1300 30.00
60 400 0.64 12.17 1600 25.00
  • Motor Type은 감속기 직결용인 피니언축으로 표시하였습니다.
    STRAIGHT축의 모터를 희망하시면 Motor Type의 PU를 S로 바꾸어 주문하십시오.
  • 그린상자표시한 모터는 UL 또는 CE규격을 적용한 TP(Thermal Protect) Type입니다
  • 삼상 380V~440V 모터에서는 인버터를 사용할 수 없습니다. 권선의 절연이 열화되어 모터가 파손될 수 있습니다.
  • For mortor with straight shaft, please write S in place of PU in Motor Type. 
  • Motor Type in green screen represents the motors with TP(Thermal Protect) according to UL or CE regulation. 
  • ※ The inverter is not available on three phase 380V~440V motors. 
  • Insulation of windings may deteriorate and damage the motor

■ RATED TORQUE OF GEARED MOTOR

(unit : kg·cm)

Speed of Geared Motor rpm 500 300 200 120 100 60 50 30 20 15 10
Gear Ratio 50Hz 3 5 7.5 12.5 15 25 30 50 75 100 150
60Hz 3.6 6 9 15 18 30 36 60 90 120 180
IH9PU180 + 9H□UB 33 55 82 123 147 221 265 300 300 300 300
IH9PU200 + 9H□UB 32 53 80 80 144 216 259 300 300 300 300
  • 그린상자표시한 감속비의 감속기는 출력축의 회전방향이 모터축의 회전방향과 반대로 됩니다.
  • 감속모터의 회전수(Speed of Geared Motor)는 모터의 회전수 (50Hz에서 1500rpm, 60Hz에서 1800rpm)를 기준하여 산출하였습니다.
    실사용시의 회전수는 부하의 크기에 따라 위의 표보다 2~15% 작게 됩니다.
  • 하얀상자부에는 감속비를 지정하여 주십시오. 감속기는 별도로 판매 됩니다.
  • The rotation of geared motor in green screen is reverse of motor rotation. 
  • Speed of Geared Motor is based on motor synchronous speed. In normal operation, the speed will be 2 to 15 percent lower than above figure. 
  • When ordering gear head, please fill blank □ with gear ratio

■ MOTOR(STRAIGHT SHAFT)  IH9S180/200  WT 3.7kg

■ GEARED MOTOR  IH9PU180/200 + 9H□ UB  WT 3.7+2.0kg

■ BOLT SIZE

TYPE BOLT SIZE
9H□ UB M6×25

■ KEY SPEC

■ DECIMAL GEAR HEAD  9H10XU  WT 0.6kg

■ WIRING DIAGRAM

   
  • 모터의 회전방향은 샤프트 끝쪽에서 볼때의 회전방향입니다.
  • 모터의 회전방향 전환은 모터가 완전히 정지한 후 실시하여 주십시오.
  • The direction of rotation is seen from the end of motor shaft.
  • Change the rotation direction of the motor only after the motor stops completely.