PRODUCT

AC Motor

□80mm 25W

기본사양

1Ph./3Ph. Motor
CONTINUOUS DUTY

제품목록

■ PERFORMANCE DATA (DUTY : CONTINUOUS)

Motor Type Output
(W)
Voltage
(V)
Freq.
(Hz)
Rating Starting Condenser
Input
(W)
Current
(A)
Torque
(kgf·cm)
Speed
(rpm)
Torque
(kgf·cm)
(V) (㎌)
IH8PF25-10 25 1ø100 50 70 0.75 1.95 1250 1.30 250 6.0
60 65 0.75 1.57 1550 1.30
IH8PF25-11 1ø110 60 75 0.75 1.57 1550 1.50 250 6.0
IH8PF25-20 25 1ø200 50 60 0.32 1.87 1300 1.30 450 1.5
60 60 0.32 1.52 1600 1.30
IH8PF25-22 1ø220 60 65 0.32 1.52 1600 1.50 450 1.5
IH8PF25-1U 25 1ø115 60 75 0.70 1.57 1550 1.50 250 5.0
IH8PF25-2C 22 1ø220 50 55 0.28 1.71 1250 1.0 450 1.3
25 1ø240 50 65 0.28 1.95 1250 1.40
IH8PF25-32 25 3ø220 50 60 0.30 1.87 1300 6.00
60 60 0.30 1.52 1600 5.00
IH8PF25-33 25 3ø380 50 60 0.17 1.87 1300 6.00
60 60 0.17 1.52 1600 5.00
IH8PF25-34 25 3ø440 50 60 0.15 1.87 1300 6.00
60 60 0.15 1.52 1600 5.00
  • Motor Type은 감속기 직결용인 피니언축으로 표시하였습니다.
    STRAIGHT축의 모터를 희망하시면 Motor Type의 PF를 S로 바꾸어 주문하십시오.
  • 그린상자표시한 모터는 UL 또는 CE규격을 적용한 TP(Thermal Protect) Type입니다
  • 삼상 380V~440V 모터에서는 인버터를 사용할 수 없습니다. 권선의 절연이 열화되어 모터가 파손될 수 있습니다.
  • For motor with straight shaft, please write S in place of PF in Motor Type. 
  • Motor Type in green screen represents the motors with TP(Thermal Protect) according to 
  • UL or CE regulation. 
  • ※ The inverter is not available on three phase 380V~440V motors. 
  • Insulation of windings may deteriorate and damage the motor

■ RATED TORQUE OF GEARED MOTOR

(unit : kg·cm)

Speed of Geared Motor rpm 500 300 200 120 100 60 50 30 20 15 10
Gear Ratio 50Hz 3 5 7.5 12.5 15 25 30 50 75 100 150
60Hz 3.6 6 9 15 18 30 36 60 90 120 180
IH8PF25 + 8H□FM 4.7 7.9 12 20 24 35 43 64 96 100 100
IH8PF25 + 8H□FB 4.6 7.6 11 19 23 34 41 62 93 100 100
  • 그린상자표시한 감속비의 감속기는 출력축의 회전방향이 모터축의 회전방향과 반대로 됩니다.
  • 감속모터의 회전수(Speed of Geared Motor)는 모터의 회전수 (50Hz에서 1500rpm, 60Hz에서 1800rpm)를 기준하여 산출하였습니다.
    실사용시의 회전수는 부하의 크기에 따라 위의 표보다 2~15% 작게 됩니다.
  • 하얀상자부에는 감속비를 지정하여 주십시오. 감속기는 별도로 판매 됩니다.
  • The rotation of geared motor in green screen is reverse of motor rotation. 
  • Speed of Geared Motor is based on motor synchronous speed. In normal operation, the speed will 
  • be 2 to 15 percent lower than above figure. 
  • When ordering gear head, please fill blank □ with gear ratio

■ MOTOR(STRAIGHT SHAFT)IH8S25WT 1.6kg

■ GEARED MOTORIH8PF25 + 8H□ FM(8H□ FB)WT 1.6+0.5/0.6kg

■ BOLT SIZE

No L(mm) GEAR RATIO BOLT SIZE
01 32 1/3 ~ 1/20 M5×60
02 42 1/25 ~ 1/200 M5×70

■ KEY SPEC

■ WIRING DIAGRAM

   
  • 모터의 회전방향은 샤프트 끝쪽에서 볼때의 회전방향입니다.
  • 모터의 회전방향 전환은 모터가 완전히 정지한 후 실시하여 주십시오.
  • The direction of rotation is seen from the end of motor shaft.
  • Change the rotation direction of the motor only after the motor stops completely.